Difference between revisions of "Hardware Setup"
Jump to navigation
Jump to search
(Created page with "== Internal Setup == === Battery === The Foenix uses an internal CR2 battery to power the Real Time Clock chip. === DIP Switches === The standard kernel interprets the DIP s...") |
(→Hard Drive Installation) |
||
| (10 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
| + | |||
== Internal Setup == | == Internal Setup == | ||
=== Battery === | === Battery === | ||
| − | The Foenix uses an internal CR2 | + | The Foenix uses an internal battery (CR2 FMX, CR2032 U/U+) to power the Real Time Clock chip. The battery is not presently required. |
=== DIP Switches === | === DIP Switches === | ||
The standard kernel interprets the DIP switches as follows: | The standard kernel interprets the DIP switches as follows: | ||
| − | * 1 - | + | * 1 - Boot options |
| − | * 2 - | + | * 2 - Boot options |
| − | * 3 - | + | * 3 - User definable |
| − | * 4 - | + | * 4 - User definable |
| − | * 5 - | + | * 5 - User definable |
| − | * 6 - | + | * 6 - off = 640x480; on = 800x600 (not yet implemented) |
| − | * 7 - | + | * 7 - Gamma correction on/off |
* 8 - IDE Drive installed | * 8 - IDE Drive installed | ||
| + | |||
| + | Boot options: | ||
| + | {| class="wikitable" | ||
| + | | 2 || 1 || effect | ||
| + | |- | ||
| + | | off || off || Boot to BASIC | ||
| + | |- | ||
| + | | off || on || Boot from SD Card (not yet implemented) | ||
| + | |- | ||
| + | | on || off || Boot from floppy (not yet implemented) | ||
| + | |- | ||
| + | | on || on || Boot from HD (not yet implemented) | ||
| + | |} | ||
=== Hard Drive Installation === | === Hard Drive Installation === | ||
| − | The Foenix | + | The Foenix supports the installation of an internal hard-drive. You will need the following: |
* A short IDE 44 Pin 2.5" laptop HDD Female-to-Female cable,eg: | * A short IDE 44 Pin 2.5" laptop HDD Female-to-Female cable,eg: | ||
| Line 27: | Line 41: | ||
* M3 screws | * M3 screws | ||
| − | == | + | == FMX Enclosures == |
| − | * M2 Inserts | + | The Foenix may be purchased as a bare board or packaged in a 3D printed enclosure; see: https://c256foenix.com/ |
| − | * M2 screws for Polycarbonate Windows | + | |
| − | * | + | === Printing your own Enclosure === |
| − | * M2.5x8mm for Floppy Installation | + | You may also print your own; the official STL files are here: |
| + | * https://cdn.discordapp.com/attachments/575557477018632213/676200823990255656/Official_Release_STL_Models_C256FOENIX_FMX.rar | ||
| + | |||
| + | In order to complete the enclosure, you will need inserts for plastic, M3/M2. You will need screws, and some Lexan cut out to complete the windows | ||
| + | |||
| + | === Screws === | ||
| + | The standard case uses the following screws: | ||
| + | * M2 Inserts: https://www.mcmaster.com/94510a360 | ||
| + | * M3 Inserts: https://www.mcmaster.com/94510a030 (Fancy one) | ||
| + | * M3 Inserts: https://www.amazon.ca/gp/product/B01IYWTCWW/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&psc=1 (Cheap one) | ||
| + | * M3 Screws: https://www.amazon.ca/gp/product/B07QQKNX5C/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1 (Cheap One) | ||
| + | * M2 screws: https://www.mcmaster.com/92010a002 - for Polycarbonate Windows | ||
| + | * RCA Connector Screw in the back: Phillips Rounded Head Screws for Sheet Metal: https://www.mcmaster.com/90184a105 | ||
| + | * M2.5x8mm for Floppy Installation - https://www.mcmaster.com/91290a102 | ||
| + | * Bumpon : FOOT CYLINDRICAL 1.5" DIA BLACK - Digikey PN#: RPC5273-ND : https://www.digikey.ca/products/en?keywords=RPC5273-ND | ||
Latest revision as of 13:29, 22 February 2021
Contents
Internal Setup
Battery
The Foenix uses an internal battery (CR2 FMX, CR2032 U/U+) to power the Real Time Clock chip. The battery is not presently required.
DIP Switches
The standard kernel interprets the DIP switches as follows:
- 1 - Boot options
- 2 - Boot options
- 3 - User definable
- 4 - User definable
- 5 - User definable
- 6 - off = 640x480; on = 800x600 (not yet implemented)
- 7 - Gamma correction on/off
- 8 - IDE Drive installed
Boot options:
| 2 | 1 | effect |
| off | off | Boot to BASIC |
| off | on | Boot from SD Card (not yet implemented) |
| on | off | Boot from floppy (not yet implemented) |
| on | on | Boot from HD (not yet implemented) |
Hard Drive Installation
The Foenix supports the installation of an internal hard-drive. You will need the following:
- A short IDE 44 Pin 2.5" laptop HDD Female-to-Female cable,eg:
- You will need Standoff, M3, 12mm high with male on one end, and female on the other
- M3 screws
FMX Enclosures
The Foenix may be purchased as a bare board or packaged in a 3D printed enclosure; see: https://c256foenix.com/
Printing your own Enclosure
You may also print your own; the official STL files are here:
In order to complete the enclosure, you will need inserts for plastic, M3/M2. You will need screws, and some Lexan cut out to complete the windows
Screws
The standard case uses the following screws:
- M2 Inserts: https://www.mcmaster.com/94510a360
- M3 Inserts: https://www.mcmaster.com/94510a030 (Fancy one)
- M3 Inserts: https://www.amazon.ca/gp/product/B01IYWTCWW/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&psc=1 (Cheap one)
- M3 Screws: https://www.amazon.ca/gp/product/B07QQKNX5C/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1 (Cheap One)
- M2 screws: https://www.mcmaster.com/92010a002 - for Polycarbonate Windows
- RCA Connector Screw in the back: Phillips Rounded Head Screws for Sheet Metal: https://www.mcmaster.com/90184a105
- M2.5x8mm for Floppy Installation - https://www.mcmaster.com/91290a102
- Bumpon : FOOT CYLINDRICAL 1.5" DIA BLACK - Digikey PN#: RPC5273-ND : https://www.digikey.ca/products/en?keywords=RPC5273-ND
