Hardware Setup

Internal Setup

Battery

The Foenix uses an internal battery (CR2 FMX, CR2032 U/U+) to power the Real Time Clock chip. The battery is not presently required.

DIP Switches

The standard kernel interprets the DIP switches as follows:

• 1 - Boot options
• 2 - Boot options
• 3 - User definable
• 4 - User definable
• 5 - User definable
• 6 - off = 640x480; on = 800x600 (not yet implemented)
• 7 - Gamma correction on/off
• 8 - IDE Drive installed

Boot options:

2	1	effect
off	off	Boot to BASIC
off	on	Boot from SD Card (not yet implemented)
on	off	Boot from floppy (not yet implemented)
on	on	Boot from HD (not yet implemented)

Hard Drive Installation

The Foenix FMX supports the installation of an internal hard-drive. You will need the following:

• A short IDE 44 Pin 2.5" laptop HDD Female-to-Female cable,eg:
  • https://www.ebay.ca/itm/IDE-44-Pin-2-5-laptop-HDD-Female-to-Female-Hard-Drive-Cable-F-F-5cm-2-inch-198-/170999956350
  • Or make your own:
    • https://www.digikey.ca/product-detail/en/3m/3625-44-30M/3M158022-1-ND/9479331
    • https://www.digikey.ca/product-detail/en/sullins-connector-solutions/SFH21-PPPN-D22-ID-BK-M181/S9083-ND/1989812
• You will need Standoff, M3, 12mm high with male on one end, and female on the other
  • https://www.mcmaster.com/93655a099
• M3 screws

FMX Enclosures

The Foenix may be purchased as a bare board or packaged in a 3D printed enclosure; see: https://c256foenix.com/

Printing your own Enclosure

You may also print your own; the official STL files are here:

• https://cdn.discordapp.com/attachments/575557477018632213/676200823990255656/Official_Release_STL_Models_C256FOENIX_FMX.rar

In order to complete the enclosure, you will need inserts for plastic, M3/M2. You will need screws, and some Lexan cut out to complete the windows

Screws

The standard case uses the following screws:

• M2 Inserts: https://www.mcmaster.com/94510a360
• M3 Inserts: https://www.mcmaster.com/94510a030 (Fancy one)
• M3 Inserts: https://www.amazon.ca/gp/product/B01IYWTCWW/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&psc=1 (Cheap one)
• M3 Screws: https://www.amazon.ca/gp/product/B07QQKNX5C/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1 (Cheap One)
• M2 screws: https://www.mcmaster.com/92010a002 - for Polycarbonate Windows
• RCA Connector Screw in the back: Phillips Rounded Head Screws for Sheet Metal: https://www.mcmaster.com/90184a105
• M2.5x8mm for Floppy Installation - https://www.mcmaster.com/91290a102
• Bumpon : FOOT CYLINDRICAL 1.5" DIA BLACK - Digikey PN#: RPC5273-ND : https://www.digikey.ca/products/en?keywords=RPC5273-ND