Difference between revisions of "Hardware Setup"
Jump to navigation
Jump to search
m (→Enclosures) |
(→Screws) |
||
| Line 52: | Line 52: | ||
=== Screws === | === Screws === | ||
The standard case uses the following screws: | The standard case uses the following screws: | ||
| − | * M2 Inserts | + | * M2 Inserts: https://www.mcmaster.com/94510a360 |
| − | * M2 screws for Polycarbonate Windows | + | * M3 Inserts: https://www.mcmaster.com/94510a030 (Fancy one) |
| + | * M3 Inserts: https://www.amazon.ca/gp/product/B01IYWTCWW/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&psc=1 (Cheap one) | ||
| + | * M3 Screws: https://www.amazon.ca/gp/product/B07QQKNX5C/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1 (Cheap One) | ||
| + | * M2 screws: https://www.mcmaster.com/92010a002 - for Polycarbonate Windows | ||
* 1 screw for the RCA Connector in the back | * 1 screw for the RCA Connector in the back | ||
| − | * M2.5x8mm for Floppy Installation | + | * M2.5x8mm for Floppy Installation - McMaster PN#: |
| + | * Bumpon : FOOT CYLINDRICAL 1.5" DIA BLACK - Digikey PN#: RPC5273-ND | ||
Revision as of 18:00, 22 February 2020
Contents
Internal Setup
Battery
The Foenix uses an internal CR2 battery to power the Real Time Clock chip. The battery is not presently required.
DIP Switches
The standard kernel interprets the DIP switches as follows:
- 1 - Boot options
- 2 - Boot options
- 3 - User definable
- 4 - User definable
- 5 - User definable
- 6 - off = 640x480; on = 800x600 (not yet implemented)
- 7 - Gamma correction on/off
- 8 - IDE Drive installed
Boot options:
| 2 | 1 | effect |
| off | off | Boot to BASIC |
| off | on | Boot from SD Card (not yet implemented) |
| on | off | Boot from floppy (not yet implemented) |
| on | on | Boot from HD (not yet implemented) |
Hard Drive Installation
The Foenix FMX supports the installation of an internal hard-drive. You will need the following:
- A short IDE 44 Pin 2.5" laptop HDD Female-to-Female cable,eg:
- You will need Standoff, M3, 12mm high with male on one end, and female on the other
- M3 screws
Enclosures
The Foenix may be purchased as a bare board or packaged in a 3D printed enclosure; see: https://c256foenix.com/
Printing your own Enclosure
You may also print your own; the official STL files are here:
In order to complete the enclosure, you will need inserts for plastic, M3/M2. You will need screws, and some Lexan cut out to complete the windows
Screws
The standard case uses the following screws:
- M2 Inserts: https://www.mcmaster.com/94510a360
- M3 Inserts: https://www.mcmaster.com/94510a030 (Fancy one)
- M3 Inserts: https://www.amazon.ca/gp/product/B01IYWTCWW/ref=ppx_yo_dt_b_asin_title_o02_s01?ie=UTF8&psc=1 (Cheap one)
- M3 Screws: https://www.amazon.ca/gp/product/B07QQKNX5C/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1 (Cheap One)
- M2 screws: https://www.mcmaster.com/92010a002 - for Polycarbonate Windows
- 1 screw for the RCA Connector in the back
- M2.5x8mm for Floppy Installation - McMaster PN#:
- Bumpon : FOOT CYLINDRICAL 1.5" DIA BLACK - Digikey PN#: RPC5273-ND
