Ports and Connectors

Front Panel

RCA Line In

These are standard RCA Line-In jacks, 2v P-P nominal.

Headphone Jack

Standard 1/8" stereo headphone jack.

SD Card

Standard SD Card slot using custom controller logic instantiated on an FPGA.

Joystick Ports

The joystick ports, from left to right, are numbered 0,1,2,3.

Ports 1 and 2 may be electrically configured as 12 bit (S)NES style ports or as TTL ports.
Ports 2 and 4 are ATARI/C64 style ports and include analog inputs.

DB9	0-1 (S)NES	0-1 TTL	2-3 ATARI/C64
1	ignored	UP	UP
2	ignored	DOWN	DOWN
3	ignored	LEFT	LEFT
4	ignored	RIGHT	RIGHT
5	LATCH	Button 1	POT-Y
6	DATA	Button 0	BUTTON
7	+5	+5	+5
8	GND	GND	GND
9	CLK	Button 2	POT-X

Reset Switch

"Power" LED

The power LED is under software control.

Rear Panel

Power Switch

Just an ordinary rocker switch.

Power

The power connector is a 12v center-positive 2.5mm barrel connector. The bare board should operate on as little as 500ma, but you should plan on more like 3A to cover adding a floppy drive, hard drive, etc.

PS/2 Keyboard and Mouse

PS/2 port 0 (Purple) -- nominal keyboard port
PS/2 port 1 (Green) -- nominal mouse port

DVI-I

The Video connector is DVI with digital and analog output suitable for use with passive VGA and HDMI adaptors.

Parallel Port

IBM Standard DB25 EPP

Serial Port

IBM Standard DB9 RS232; all pins implemented.

MIDI

The port on the left (closest to the serial port) is MIDI OUT.
The port on the right (closest to the RCA jacks) is MIDI IN.

Line Out

These are standard RCA Line-Out jacks, 2v P-P nominal.

Internal

J2 (Serial)

The 8-pin serial header follows the DTK/INTEL standard:

P2 (IDE)

Standard 44 Pin 2.5" laptop HDD IDC header.

J-TAG

Standard 10-pin J-TAG connector for reprogramming the FPGAs.

FLOPPY0 and FLOPPY1

FLOPPY0 and FLOPPY1 are electrically standard 3.5" micro Floppy Disk Drive connectors (26 pins FPC Cable).

The internal drive is expected to be connected to FLOPPY0.

CN1

J-TAG interface for programming the TRINITY and UNITY FPGAs.

Side Panel

Expansion Connector

Odd	Description	Even	Description
1	GND	2	GND
3	CPU D0 (I/O)	4	CPU D1 (I/O)
5	CPU D2 (I/O)	6	CPU D3 (I/O)
7	CPU D4 (I/O)	8	CPU D5 (I/O)
9	CPU D6 (I/O)	10	CPU D7 (I/O)
11	GND	12	GND
13	CPU A0	14	CPU A1
15	CPU A2	16	CPU A3
17	CPU A4	18	CPU A5
19	CPU A6	20	CPU A7
21	CPU A8	22	CPU A9
23	CPU A10	24	CPU A11
25	CPU A12	26	CPU A13
27	CPU A14	28	CPU A15
29	CPU A16	30	CPU A17
31	CPU A18	32	CPU A19
33	CPU A20	34	CPU A21
35	CPU A22	36	CPU A23
37	GND	38	GND
39	EXP_RDY* (I)	40	BUS_VPA (O)
41	BUS_R/Wn (O)	42	BUS_VDA (O)
43	SYS_RSTn (OC)	44	BUS_REQn (OC)
45	BUS_NMIn (OC)	46	BUS_ACKn (O)
47	EXP_CSn**(O)	48	EXP_ACTn*** (OC)
49	EXP_CLK(O)	50	EXP_INTn(I)
51	GND	52	GND
53	+5V	54	+5V
55	+12V	56	EXP_LINE_IN_R (IA)
57	+12V	58	EXP_LINE_IN_L (IA)
59	+3V	60	+3V

(I/O) : Input/Output

(I) : Input

(O) : Output

(OC) : Output Collector (Wired Or) Bring down with OC Driver

(IA) : Input Analog (Audio Signal Input - Line Level)

EXP_RDY: This is the ready Line that will hold the bus thus stretching the cycle to allow slower devices to respond. Set to 1 to add delay, 0 for normal operation.
- EXP_CSn: This is the Chip Select for the Expansion Card Zone: $AE:0000 - $AE:FFFF - for Compatibility reasons any I/O Card ought to be mapped into this area unless it requires more memory mapping.
  - EXP_ACTn: Bring this signal to ground for an expansion card to be recognized by the system.

POWER ALLOCATION FOR EXPANSION CARD:

+3V3: Please don't use more than 500mA for the +3.3Volt Rail.

+5V: Please don't use more than 500mA for the +5Volt Rail. The system doesn't use a lot of +5V, but there are spurious needs for +5V rail when an HDD (spinning) is installed in the system.

+12V: The limit of current you can draw on the +12V is related to the power supply you are using for your machine. It is better to use that power supply to derive any other from.